E01 ELECTRICAL INTERFACES AND BENCH CHARACTERIZATION Authored engineering review, 6 October 2026 The present operating model takes actual RMS voltage across the driver as its input. A computer volume setting is not that voltage. The complete electrical chain still needs physical calibration before any model-to-hardware claim. No hardware was powered or measured for this document. PROPOSED WIRED CHAIN Computer audio application -> selected analog output or USB audio DAC -> 3.5 mm audio cable -> Dayton KAB-FC AUX harness -> KAB-215v2 amplifier -> separate speaker output pair -> ND64-4 or ND91-4 in the declared enclosure. An enclosed external low-voltage DC supply powers the amplifier separately. The amplifier is not itself a USB measurement interface. USB audio hardware, recording inputs, sensors, supply model and exact end connectors remain parts to select and characterize. Bluetooth is outside the deterministic timing path. VERIFIED MANUFACTURER INTERFACES The amplifier's official guide identifies its included power/speaker harnesses, the optional AUX harness, and the AUX jumper that must be removed. Use the matched harness and the illustrated orientation. The driver end of that harness is not thereby proven to fit a speaker tab without soldering. Driver terminal width, thickness, mating connector and pull-out clearance remain unresolved. The source supports a 12-24V DC supply range and 4-8ohm nominal speaker load; its 2x15W rating is specified at19V into8ohms, not at every operating condition. https://www.daytonaudio.com/images/resources/325-500--dayton-audio-kab-215v2-quick-start-wiring-guide.pdf https://www.daytonaudio.com/product/1871/kab-215v2-2-x-15w-class-d-audio-amplifier-board-with-bluetooth-5-0 https://www.daytonaudio.com/product/1394/kab-fc-functional-cables-package-for-bluetooth-amplifier-boards OUTPUT GROUNDING AND MEASUREMENT Each speaker belongs between its own marked plus/minus output pair. The negative output is not assumed to be computer, supply or oscilloscope ground. Do not tie channel outputs together or attach an earth-grounded probe clip to an output terminal. A differential measurement interface must have suitable input range, common-mode range, isolation/grounding arrangement and bandwidth. Class-D switching components can corrupt an unqualified RMS meter or sound card input; use an appropriate measurement front end and documented filtering. Do not connect amplified speaker outputs directly to a PC microphone/line input. TI's manufacturer notes establish these general differential/Class-D measurement principles; they are not a schematic certification of the Dayton board. https://www.ti.com/lit/an/sloa116/sloa116.pdf https://www.ti.com/lit/an/sloa068a/sloa068a.pdf CHARACTERIZATION SEQUENCE — PROPOSED, NOT PERFORMED 1. Record the physical component revisions, measured mounting interfaces, actual enclosure air-volume basis, complete signal path and supply. Resolve polarity/connector/insulation/strain-relief issues before applying power. 2. Establish the measurement chain's gain, phase, bandwidth and uncertainty with its documented calibration procedure. Record instrument and probe models, calibration dates, ranges, filters and grounding diagram. 3. With the intended load and conservative initial drive, measure differential terminal voltage at the model's test frequencies. Record digital amplitude, computer/DAC settings and amplifier volume position; these settings are only reproducibility metadata, not substitutes for measured volts. 4. Confirm unclipped waveform behavior, channel polarity, frequency response, left/right phase and repeatability. Change the amplifier/supply/cable only as a new configuration. Measure the output again after changes. Do not infer a fixed gain or latency from an undocumented amplifier setting. 5. For driver comparison, acquire voltage and current with synchronized, calibrated channels and compare complex impedance against the declared model. If using a series current-sense element, include its calibrated value, phase behavior and added series impedance in the model and uncertainty. 6. Measure cone motion separately when validating displacement. An enclosure pressure estimate is not measured external SPL, and an accelerometer added to a small cone changes its moving mass. Record that loading if used. 7. Compare repeated measurements with the model plus the measured uncertainty. Preserve discrepancies, temperature drift and rejected runs. Do not adjust the model after looking at a result and still label that result a prediction. WHAT THE MODEL DOES AND DOES NOT ACCOUNT FOR The reciprocal three-state model includes coil resistance/inductance, back EMF, motor force, effective moving mass, suspension, aggregate mechanical damping and ideal sealed-air stiffness. Its power balance is internal to that model. The aggregate mechanical-loss term is not independently measured acoustic power. The calculation does not separate radiation from suspension losses, predict a beam of sound, or predict specimen fracture. The Dayton Mms already includes air load; another full radiation mass must not be added silently. For a reactive speaker, real output power is the time average of v(t)i(t), or the real part of the RMS complex power for a steady sinusoid. Vrms^2 divided by nominal4ohms is not a valid general loudspeaker power measurement. Amplifier DC input power and wall input power are separate measurements with different boundaries. Record idle energy, startup, electronics, sensors and any repetition or reset hardware if later making whole-system efficiency claims. BUILD STATUS The PC-to-amplifier architecture is specified at interface level. A completely solder-free chain, exact PCB carrier holes, supplied driver fit and measured operation have not been established. There is no physical fracture result in this package. The next useful evidence is a calibrated low-amplitude electrical and motion measurement of the assembled head, not a higher unmeasured setting.