EL01 - WIRED E01-A CONNECTION REGISTER Reviewed 2026-10-06. Documented candidate interfaces; zero physical tests. The purpose of this edition is to close the named-component and connection gaps in the small acoustic bench. The numerical E01 model is not proof that this electrical chain is calibrated or assembled. The parts register explicitly retains the terminal, enclosure and measurement gaps that prevent a finished no-solder build claim. Signal path PC USB-A data port -> StarTech ICUSBAUDIO2D -> its analog line-out/SPDIF combo jack -> StarTech MU3MMS TRS cable -> Dayton KAB-PMV3 AUX jack and supplied matched harness -> KAB-215v2 AUX port (manufacturer guide callout 3). Use the DAC's Direct EQ setting and one analog output only. Its optical output and microphone input are not in this route. The board's AUX jumper must be removed as illustrated by Dayton before the matched AUX harness is inserted. Board-side AUX header numbering is not provided here: the manufacturer's matched plug is the interface, not a guessed replacement connector. Bluetooth is not used as the research signal source. Wired audio still needs measured latency, gain and phase characterization. [S02, S04, S05] Power and controls Grounded North American outlet -> StarTech PXT101 factory cord -> Mean Well GST40A15-P1J enclosed supply -> factory P1J plug -> PMV3 DC jack/harness -> board DC input, callout 2. The supply is a 15 V candidate inside the amplifier's stated operating range. Its center-positive barrel has the catalog diameter of the PMV3 jack; insertion depth, retention and the actual jack-to-board polarity still require verification. Do not open the supply or fabricate mains wiring. Unpowered continuity must establish DC+ and DC- through the received matched harness before power is applied; this document assigns no unverified header pin numbers. Available supply current does not force that current through the speaker and does not establish a suitable fuse or harness limit. [S01, S03, S08, S09] PMV3 volume harness -> callout 4; PMV3 rocker harness -> callout 6. The rocker is a board control, not an AC isolator or emergency stop. The factory supply must remain accessible for disconnection. The kit already includes these controls, so a separate KAB-FC kit is not counted. Battery charging and pairing controls are outside this bench route. [S01-S03, S16] One driver, one channel Use the included speaker harness in the manufacturer's J2 orientation. Left positive is pin 2; left negative is pin 4. These connect to the ND64's marked positive and negative terminals after the actual tab dimensions and a retaining insulated termination are qualified. Pins 1 and 3 are the unused right pair and must be insulated separately. Do not join speaker negatives, ground either output, parallel channels or add a bridge connection. The drawing's MOLEX-4PIN-3MM label is not enough to choose a generic connector from a catalog. [S02] The manufacturer sources used here do not give the ND64 terminal tab width/thickness or a mating connector part number. No 2.8 mm, 4.8 mm or 6.3 mm quick-disconnect is assumed. Measure both actual tabs, confirm harness wire gauge and access, then qualify the matching crimp termination and tool with a retention check. This unresolved interface remains visible in BOM row E08. Temporary measurement clips are not permanent vibration-resistant speaker terminations. [S10, S11] Electronics placement The panel kit provides mounting hardware, but this register does not assert that its board, terminals and bend radii fit a completed housing. Place the panel/amplifier in a separate external electronics enclosure; retain its dimensions, strain relief, ventilation and insulated test points as explicit mechanical work. The frozen E01 acoustic cavity remains unchanged. The external board cover/protection is pending, not an assembled feature. Do not place extra hardware inside the frozen acoustic cavity without recomputing its net air volume. The PMV3 panel is a catalog component, not a replacement for the E01 acoustic baffle. Measurement boundary Read MEASUREMENT-INTERFACES.json alongside this document. The candidate AD3 uses its differential MTE inputs: scope1+ senses the selected speaker + and scope1- senses that same speaker -. Neither is a ground clip. The instrument ground reference belongs only on a qualified amplifier DC-ground net after reviewing the complete USB/audio/supply ground paths. Differential input does not provide galvanic isolation. A grounded single-ended BNC arrangement across a bridge output is not this connection. Never feed an amplified speaker output into the PC audio input. [S12-S14] With a 15 V Class-D supply, the small audio fundamental does not justify the instrument's low input range: each switched terminal has a ground-referenced common-mode level. High-range operation and transient limits need verification. The published typical +/-100 mV plus 0.5% high-range accuracy does not establish precise measurement of the 0.1 Vrms numerical cases. A documented calibration and uncertainty budget must qualify that comparison. Separate the audio fundamental from raw switching-content RMS and preserve the acquisition/filter settings. [S14] Voltage sensing alone cannot prove electrical input energy or efficiency. A synchronized, qualified current channel remains a separate gap. The UMM-6 records airborne sound; it does not measure specimen stress, force or diamond vibration. Separate USB output and microphone clocks do not prove exact mechanical timing. Microphone response and measurement limits are in the companion. [S15] Evidence to record before a physical claim - Photographs/part revisions and measured terminal sizes; no credentials or unrelated private material. - Unpowered connector continuity, retained wiring, supply label/polarity, ground paths and clip/test-point fit. - Actual DAC/PC settings, amplifier gain, frequency-dependent terminal fundamental voltage, clipping and idle behavior with the intended load. - Motion/excursion and thermal observations within the qualified bench envelope; a thermal wattage rating is not a low-frequency excursion limit. - Instrument calibration, uncertainty, timing, raw traces, processing settings and unsuccessful runs. No hardware was energized during preparation. The research program currently calculates models; it is not a calibrated signal generator or an automatic instrument controller. All proposed checks above remain unperformed. There is no claim of material fracture from this low-power loudspeaker chain. Manual impact and powered reset The E01 gravity cartridge is manually lifted and released and requires no drive electronics. A future automatic reset needs its own selected actuator, driver, controller, end stops, latch/release mechanism, supply, protection and wiring. Those parts cannot be selected from an actuator's nameplate force alone; their force/stroke/speed/duty and disengagement must match the physical cartridge. They remain outside the acoustic BOM. Cost and source handling The JSON keeps included kit components from being counted again, separates MSRP from observed prices, and leaves the full total unknown. No purchase or complete under-$1,000 claim is made. ELECTRONICS-SOURCES.json resolves every source identifier to a primary manufacturer URL and records dates/limits. This edition contains authored summaries only; vendor PDFs, photographs and drawing files are not redistributed.